DPF service in Tbilisi

DPF OFF Diesel particulate filter
software deactivation

The DPF (Diesel Particulate Filter) traps solid particles in diesel engine exhaust. If there is a warning, frequent regeneration or reduced power, we use diagnostics to identify the cause and explain whether cleaning or repairs are needed, or software deactivation is possible.

How the DPF works
Illustrated DPF and catalyst cutaway with pressure and temperature sensors

01

Filtration

Pressure difference
18mbar
Temperature
275°C

Gas passes through the porous walls while soot particles remain in the filter.

Readings and motion are illustrative.

How the system works

What is a DPF and how does it work?

The DPF (Diesel Particulate Filter) is a soot filter that traps solid particles in diesel exhaust. Alternately plugged ends of the longitudinal channels force the exhaust through porous walls, while soot remains in the filter.

During regeneration, soot burns off at a high temperature. The process may occur naturally or be initiated by the ECU. The ECU assesses filter loading using pressure difference, temperature and other data.

Short trips and insufficient temperature may prevent regeneration from completing. Accumulated ash does not burn off during regeneration and requires separate cleaning.

Software changes

  • DPF control logic is disabled in the software
  • Active regeneration logic is disabled in the software
  • Fault codes related to this system are disabled
  • Software limits imposed because of the DPF are removed
  • Other DPF-related software parameters are changed according to the vehicle and ECU

Software cannot fix physical faults. We separately check sensors, pipes and wiring, as well as excessive soot caused by the engine, injectors or turbocharger.

Recognising the problem

What are the signs of a problem?

  • Warnings and fault codes

    The display shows a message that the filter is full or needs cleaning. Diagnostics may also reveal a fault related to the DPF pressure sensor.

  • Reduced power

    The vehicle loses power or enters limp mode. We check whether the restriction is caused by the DPF or another fault.

  • Regeneration and fuel consumption

    The cleaning cycle repeats unusually often or fails to complete. Fuel consumption may also rise under the same conditions.

DPF deactivation requires software and mechanical work. Along with software deactivation, the filter element must be physically removed so exhaust can flow freely. We agree both jobs with you in advance.

Stages

Four stages of the work

  1. Diagnostics and readingWe check fault codes and data from the filter, sensors and engine. We read the ECU file using OBD, Bench or Boot.
  2. Custom calibrationWe process the file for the specific vehicle, disabling DPF control logic, regeneration and the relevant fault codes.
  3. Writing the softwareWe write the processed file to the ECU and verify that writing is complete.
  4. TestingWe check vehicle operation, live data and DPF-related faults.

Questions and answers

Frequently asked questions

Which vehicles do we work on?

Diesel passenger cars and trucks equipped with a DPF, regardless of make. We determine whether the work is possible based on the specific ECU and diagnostic results.

Is DPF deactivation always necessary?

No. The cause may be incomplete regeneration, a faulty sensor, a dirty filter or damage to the filter. After diagnostics, we explain whether cleaning, repair or replacement is needed and what software deactivation would change.

Will the Check Engine light come on after DPF OFF?

Software deactivation addresses DPF-related faults. If another system malfunctions, the Check Engine light may come on again. Such causes require separate diagnostics.

Will I pass the vehicle inspection?

After DPF deactivation, the inspection result depends on the vehicle’s technical condition. In our experience, if the engine and the fuel and air supply systems work properly, there may be no visible smoke. This is a favourable starting point, but we cannot promise in advance that the vehicle will pass inspection.

Mercedes-Benz X253, 2017 · 2.2 L — DPF, EGR, AdBlue, Start/Stop software deactivation.

Work completed

Mercedes-Benz X253

2017 · 2.2 L

DPF, EGR, AdBlue, Start/Stop software deactivation.

View this project

Send us a photo of the warning

Provide the vehicle model, year and engine. Attach a photo of the display or a fault code. We will explain what checks are needed and how to proceed. The consultation is free.

Call WhatsApp